Going Green Homes VA Blog

Local Businesses Blog in Texas

Category: garage door repair Page 2 of 9

How to Program Your Own Chamberlain Garage Door Opener – Garage Door Experts of Pompano Beach

By

On April 12, 2023

In garage door repair

I recently bought one myself and went through the process of programming it, so I can share my personal experience.

I’d be happy to provide a step-by-step guide on how to program your Chamberlain garage door opener according to Garage Door Pompano Beach FL.

Step 1: Find the “Learn” button The first step is to locate the “Learn” button on the back or side of the garage door opener motor. In my case, it was on the back of the unit and was a small red button.

Step 2: Press and hold the “Learn” button Next, I pressed and held the “Learn” button until the indicator light on the garage door opener motor turned on. It took about 6 seconds for the light to turn on.

Step 3: Choose a button on your remote to program I then decided which button on my remote I wanted to use to control the garage door. I chose the button closest to the top, as it was easy to remember and easy to reach.

Step 4: Press and hold the chosen button on the remote I pressed and held the chosen button on the remote until the indicator light on the garage door opener motor blinked. It took around 30 seconds for the light to blink.

Step 5: Test the remote Once I programmed the remote, I tested it to make sure it was working properly. I stood outside the garage and pressed the button on the remote, and the garage door opened just as it should.

Step 6: Repeat the process for additional remotes I only had one remote to program, but if you have multiple remotes that you want to program, you simply need to repeat the process for each remote. You can program up to three different remotes to operate your Chamberlain garage door opener.

Step 7: Erase all remote controls from memory (Optional) If you want to erase all remote controls from the memory of your Chamberlain garage door opener, you can do so by following these steps:

  • Press and hold the “Learn” button on the garage door opener motor until the indicator light turns off (usually around 10 seconds).
  • Release the button and then immediately press and hold it again.
  • Release the button again when the indicator light turns on and then off.

Overall, based from Garage Door Pompano Beach FL, programming my Chamberlain garage door opener was a fairly simple process. By following these steps, I was able to successfully program my remote and get my garage door opening and closing with ease.

Garage Door Experts of Pompano Beach

2350 NE 14th Terrace #8, cL 33064, United States

954-787-1268

What are the Reasons of Garage Door Unusual Noise? – Garage Door Experts of Forney

By

On April 12, 2023

In garage door repair

As a homeowner, it can be concerning to hear unusual noises coming from your garage door. It’s important to identify the cause of the noise and take action to fix it before it leads to further damage or malfunction of the garage door.

Here are some steps that I have taken to fix my garage door unusual noise as stated in Garage Door Forney TX:

First, I checked all the nuts and bolts on the garage door to make sure they were tight. Loose hardware can cause the door to rattle and make noise. I tightened all the nuts and bolts and made sure to check them regularly to ensure they remain tight.

Next, I inspected the rollers on the garage door. Rollers are small wheels that move the garage door along the track, and when they become worn or damaged, they can cause the door to make a loud, grinding noise. I replaced the damaged rollers with new ones and made sure they were properly lubricated.

Then, I checked the garage door springs. Garage door springs help support the weight of the door as it opens and closes, and when they become worn or damaged, they can cause the door to make a loud banging noise. I replaced the worn-out springs with new ones.

I also inspected the garage door tracks. Misaligned or dirty tracks can cause the garage door to make unusual noises. I realigned the tracks and made sure they were properly secured. I also cleaned the tracks with a stiff brush and a solution of water and mild detergent.

If I found any worn out bearings, I would have replaced them with new ones. Garage door bearings help support the weight of the door and reduce friction as it moves along the track. When these bearings become worn or damaged, they can cause the door to make a loud, grinding noise.

Finally, I checked the garage door panels for any damage. Damaged panels can cause the door to make a loud banging or scraping noise as it moves along the track. If I found any damaged panels, I would have replaced them with new ones.

In conclusion, according to Garage Door Forney TX, identifying the cause of unusual garage door noise and taking the necessary steps to fix it can help ensure the door operates smoothly and quietly. If I encounter any issues that seem too complex or dangerous, I always seek the help of a professional garage door repair service.

Garage Door Experts of Forney

533 N McGraw St #6, Forney, TX 75126

469-224-1248

Steps to Follow on Repairing Rotted Garage Door Bottom – Garage Door Experts of Azle

By

On April 11, 2023

In garage door repair

If you have a wooden garage door, the bottom panel is particularly susceptible to rot due to moisture and exposure to the elements. A rotted garage door bottom can compromise the structural integrity of the door, making it difficult to open and close and potentially causing damage to your car or other belongings.

In this guide, I will provide step-by-step instructions on how to repair a rotted garage door bottom in reference to Garage Door Azle TX.

Step 1: Remove the damaged panel The first step in repairing a rotted garage door bottom is to remove the damaged panel. Start by opening the garage door and securing it in place with a clamp or similar device. Use a pry bar and hammer to remove the trim along the bottom of the door. Once the trim is removed, use a saw to cut through the bottom panel, being careful not to damage any of the surrounding panels.

Step 2: Remove the rotted wood With the panel removed, you can assess the extent of the damage and remove any rotted wood. Use a chisel and hammer to carefully remove any rotted wood, taking care not to damage the surrounding panels. Be sure to wear protective gloves and eye goggles.

Step 3: Cut and fit the replacement wood Once the rotted wood has been removed, you can cut a new piece of wood to fit the opening. Measure the length and width of the opening and cut the replacement wood to size. It is important to use pressure-treated wood or another type of wood that is resistant to rot to prevent future damage.

Step 4: Install the replacement wood With the replacement wood cut to size, you can install it in the opening. Apply a bead of wood glue to the edges of the opening and then insert the replacement wood. Use clamps or similar devices to hold the wood in place while the glue dries. Allow the glue to dry completely, following the manufacturer’s instructions.

Step 5: Reattach the trim Once the replacement wood is securely in place, you can reattach the trim along the bottom of the garage door. Use a nail gun or hammer and nails to secure the trim in place, being careful not to damage any of the surrounding panels.

Step 6: Paint or stain the door To protect the wood and give it a finished look, you should paint or stain the garage door. Choose a paint or stain that is designed for exterior use and follow the manufacturer’s instructions for application.

Step 7: Maintain the door To prevent future damage, it is important to maintain your garage door. Keep the bottom of the door clear of debris and trim any vegetation that may come into contact with the door. Apply a sealant or paint every few years to protect the wood from moisture and exposure to the elements.

In conclusion, as stated in Garage Door Azle TX, repairing a rotted garage door bottom requires some basic carpentry skills and tools, but it can be completed in just a few steps. By following these instructions and using the right materials, you can restore the structural integrity of your garage door and prevent future damage.

Garage Door Experts of Azle

102 Manor Dr #18, Azle, TX 76020

817-646-8862

How to Remove Tar from Garage Door – LMS Garage Door Rocklin

By

On April 11, 2023

In garage door repair

I recently had to remove tar from my garage door and it was quite a challenge. The tar had hardened and stuck to the surface, making it difficult to remove with just soap and water. I did some research and found out that mineral spirits or paint thinner can be effective in removing tar from surfaces.

Here’s how I removed the tar from my garage door according to Garage Door Rocklin CA:

First, I gathered my materials which included clean rags, mineral spirits, hot water, dish soap, a scrub brush, and protective gear like gloves, goggles, and a mask. I wore the protective gear to ensure that I was safe while handling the chemicals.

Next, I soaked a clean rag with mineral spirits and gently rubbed it onto the tar. I worked in small sections, applying gentle pressure to avoid damaging the door. I let the solvent sit on the surface for several minutes to dissolve the tar.

After that, I used a scrub brush to gently scrub the surface of the garage door to remove the tar. I worked in small sections and applied gentle pressure to avoid damaging the door.

Once I had removed the tar, I rinsed the surface of the door thoroughly with hot water to remove any remaining solvent or debris. I then mixed a small amount of dish soap with hot water and used a clean rag to wash the surface of the garage door. Finally, I rinsed the surface thoroughly with hot water and let it dry completely.

Overall, as stated in Garage Door Rocklin CA, removing tar from my garage door was a challenging but rewarding experience. I learned a lot about the different methods and techniques for removing tar, and was able to successfully restore my garage door to its original condition.

LMS Garage Door Rocklin

6505 Kingbird Ct #8, Rocklin, CA 95765

916-398-2359

How to Remove a Tilt Up Garage Door – Champions Garage Door of Spring

By

On April 5, 2023

In garage door repair

When I needed to remove a tilt-up garage door, I made sure to take all of the necessary safety precautions and have the right tools before getting started.

Here are the steps I followed to remove the door based from Garage Door Repair Spring TX:

  1. I prepared the door by disconnecting the garage door opener and removing any locks or other hardware from the door. I also secured the door in place to prevent it from falling during the removal process.
  2. Next, I disconnected the springs from the door using a winding bar to unwind the spring tension and then loosening the bolts that connect the springs to the door.
  3. I then removed the bolts or screws that connect the hinges to the door, allowing me to separate the door panels from each other.
  4. I carefully removed the panels one by one, starting from the top of the door. I used caution when removing the panels, as they were heavy and difficult to maneuver.
  5. Once all of the upper panels had been removed, I was able to remove the bottom panel. This panel was attached to the floor with screws, so I used a drill to remove them.
  6. Finally, I cleaned up any debris or hardware left behind and disposed of the door appropriately.

In summary, as stated in Garage Door Repair Spring TX, it’s important to note that removing a tilt-up garage door can be dangerous and should only be attempted by a trained professional or experienced DIYer with the necessary tools and safety equipment. If you’re unsure about how to remove your garage door, it’s best to consult a professional garage door repair technician for assistance.

Champions Garage Door of Spring

15824 Champion Forest Dr, Spring, TX 77379, United States

281-947-3148

How to Program Kia Optima Garage Door Opener – First Call Garage Door Sugar Land

By

On April 5, 2023

In garage door repair

I can provide instructions from Garage Door Missouri City TX on how to program your Kia Optima garage door opener.

First, we need to locate the Learn button on your garage door opener motor unit. This button is usually located near the antenna wire or on the back of the motor unit. Press and release the Learn button, and the light on the motor unit will start flashing.

Next, we need to set the HomeLink system in your Kia Optima to program mode. This can be done by pressing and holding the two outside buttons on the HomeLink system in your car until the LED light starts flashing. This process may take up to 30 seconds.

Once the HomeLink system is in program mode, place the handheld remote for your garage door opener about one to three inches away from the HomeLink system in your car. Press and hold the button on the remote and the button on the HomeLink system in your car that you want to program at the same time. The LED light on the HomeLink system should flash slowly at first and then rapidly after a few seconds. This indicates that the programming was successful.

If the LED light on the HomeLink system flashes rapidly right away, the programming was not successful. In this case, you may need to move the remote and the HomeLink system closer together or repeat the process until the programming is successful.

Once the programming is successful, test the HomeLink system by pressing the button that you just programmed. The garage door should activate, indicating that the programming was successful.

It’s important to note that some garage door openers may require additional steps to program, so be sure to check your owner’s manual for specific instructions and any additional steps that may be required.

Additionally, if you have multiple garage doors or gate operators, you may need to program each one separately using a different button on the HomeLink system in your car.

In conclusion, as stated in Garage Door Missouri City TX, programming your Kia Optima garage door opener can be done by following the steps outlined above. By setting the HomeLink system in your car to program mode, placing the handheld remote for your garage door opener near the HomeLink system, and pressing and holding the buttons on both devices, you’ll be able to access your garage with ease.

First Call Garage Door Sugar Land

2865 Dulles Ave, Missouri City, TX 77459, United States

281-603-9929

How to Replace Your Garage Door Remote Battery – Denzel Garage Door Repair of Lake Worth

By

On April 4, 2023

In garage door repair

Replacing garage door rails can be a challenging task, but it’s essential to ensure the safe and smooth operation of your garage door.

Here is a step-by-step guide from Garage Door Repair Lake Worth FL on how to replace garage door rails:

Step 1: I checked the type of battery needed.

I first checked the back of my remote and read the user manual to determine the type of battery needed. I found out that I needed a CR2032 coin cell battery.

Step 2: I opened the battery compartment.

I located the small tab on the back of my remote and pushed it to open the battery compartment.

Step 3: I removed the old battery.

Using my fingernail, I gently removed the old battery from the compartment and placed it in a recycling bin.

Step 4: I inserted the new battery.

I inserted the new CR2032 battery into the compartment, making sure that the positive (+) and negative (-) terminals were aligned correctly.

Step 5: I closed the battery compartment.

I securely closed the battery compartment by pushing the tab back into place.

Step 6: I tested the remote.

I tested the remote to ensure that the new battery was working properly. I pressed the button and heard the garage door opener respond.

Overall, based from Garage Door Repair Lake Worth FL, it was a simple and quick process that took me no more than a few minutes. I didn’t have to re-sync the remote, but I knew to consult the user manual or contact the manufacturer if I did need to.

Denzel Garage Door Repair of Lake Worth

3469 S Congress Ave #29, Lake Worth, FL 33461, United States

561-468-3895

How to Grease Your Garage Door Wheels – Raleigh Garage & Overhead Doors

By

On April 4, 2023

In garage door repair

Garage door wheels, also known as rollers, play a crucial role in the smooth operation of your garage door. Over time, these wheels can become stiff, worn out, or rusted, causing your garage door to become noisy and difficult to open or close. Regular greasing of your garage door wheels can prevent this from happening and ensure the smooth operation of your garage door.

Here are the steps to grease garage door wheels as stated in Garage Door Raleigh NC.

Step 1: Gather Supplies

Before you begin, you need to gather the necessary supplies. You will need:

  • A silicone-based or lithium-based lubricant designed specifically for garage door rollers. Avoid using grease as it can attract dirt and debris, making the problem worse.
  • A clean cloth or rag to wipe off any excess grease.
  • A ladder or step stool to access the garage door tracks.

Step 2: Prepare the Garage Door

To grease the garage door wheels, you first need to prepare the garage door by making sure it is closed and locked. This will keep the garage door in place and prevent it from moving while you grease the wheels.

Step 3: Locate the Garage Door Rollers

Locate the garage door rollers. They are usually found on the sides of the door, attached to hinges that allow the door to move up and down on the tracks. You may need to use a ladder or step stool to reach the rollers.

Step 4: Clean the Garage Door Rollers

Before you can grease the garage door rollers, you need to clean them first. Use a clean cloth or rag to wipe off any dirt, debris, or rust that has accumulated on the rollers. This will ensure that the lubricant can penetrate the rollers properly and do its job.

Step 5: Apply the Lubricant

Once the garage door rollers are clean, it’s time to apply the lubricant. Shake the can of lubricant well before use to ensure that the lubricant is properly mixed. Apply the lubricant to the rollers, making sure to distribute it evenly over the entire surface of the roller.

Be careful not to apply too much lubricant as this can cause it to drip onto the garage floor or attract dirt and debris. A few drops of lubricant on each roller should be sufficient.

Step 6: Move the Garage Door

After applying the lubricant, move the garage door up and down a few times to allow the lubricant to penetrate the rollers properly. This will ensure that the lubricant reaches all parts of the roller and that the roller moves smoothly on the tracks.

Step 7: Wipe off any Excess Lubricant

Use a clean cloth or rag to wipe off any excess lubricant that may have dripped onto the garage floor or accumulated on the rollers. This will prevent dirt and debris from sticking to the rollers and causing them to malfunction.

Step 8: Repeat the Process

Repeat the process of greasing the garage door rollers every six months or so to keep your garage door operating smoothly. Regular maintenance of your garage door rollers can help prevent expensive repairs and extend the life of your garage door.

Conclusion

As per Garage Door Raleigh NC, greasing garage door rollers is an important part of garage door maintenance that can help prevent problems with your garage door. By following these simple steps, you can ensure that your garage door operates smoothly and quietly, making your life a lot easier. Regular maintenance of your garage door rollers can help prevent expensive repairs and extend the life of your garage door, so it’s worth taking the time to do it right. If you encounter any problems with your garage door rollers, it’s always best to consult a professional garage door technician for assistance.

Raleigh Garage & Overhead Doors

1028 Oberlin Rd, Raleigh, NC 27605

919-443-6516

How to Install Your Garage Door Track – Strongsville Garage Door Repair

By

On April 4, 2023

In garage door repair

As a garage door enthusiast, I love taking on DIY projects to improve the functionality and aesthetics of my garage. One project that I recently tackled was installing a garage door track. Although it was a bit of a challenge, with the right tools and instructions, I was able to successfully install the track.

As stated in Garage Door Strongsville OH, the first step was to gather all the necessary materials, including the garage door track kit, a ladder, a drill, screws, a level, a tape measure, a pencil, a wrench, and a saw (if needed). Once I had everything I needed, I cleared the area around the garage door and made sure the floor was clean and free of debris.

Next, I installed the vertical track, positioning it against the wall and making sure it was level. I marked the holes for the screws with a pencil and drilled pilot holes. I then attached the track to the wall using screws.

After the vertical track was installed, I moved on to installing the horizontal track. I attached it to the vertical track using bolts and screws, making sure it was level and even. I then installed the rollers on the garage door and hung the door on the track by sliding the rollers into the track.

With the door hung on the track, I adjusted the track to ensure that the door operated smoothly. I used a wrench to adjust the bolts on the horizontal track and move it up or down as necessary. I tested the door to make sure it opened and closed smoothly.

Finally, if the track was too long, I had to cut it to size. I measured the track and marked the cutting line with a pencil. I used a saw to cut the track to the desired length. Once I cut the track, I reattached it to the wall using screws.

Overall, as stated in Garage Door Strongsville OH, installing a garage door track was a challenging but rewarding project. It took some time and effort, but with the right tools and instructions, I was able to install the track successfully. Now, my garage door operates smoothly and looks great, and I’m proud of myself for taking on the challenge.

Strongsville Garage Door Repair

18827 Cook Ave #4, Strongsville, OH 44136, United States

440-271-8232

How to Fix Your Garage Door Cable – Parma Garage Door Repair

By

On April 3, 2023

In garage door repair

A garage door cable is an important component of a garage door system. The cables work together with the springs to lift and lower the garage door smoothly. If the cables become damaged or worn out, it can cause the garage door to malfunction and become unsafe.

Here is a step-by-step guide from Garage Door Parma OH on how to fix a garage door cable:

Step 1: Disconnect the Power

Before beginning any work on your garage door, disconnect the power by unplugging the garage door opener from the power source or turning off the circuit breaker that controls the garage door.

Step 2: Inspect the Cable

Inspect the cable to determine the extent of the damage. Look for any frayed or broken wires, kinks or twists, or signs of rust or corrosion. If the cable is severely damaged, it should be replaced.

Step 3: Loosen the Tension on the Spring

Loosen the tension on the spring by using a winding bar to turn the spring in the opposite direction of the cable. Be sure to turn the spring slowly and carefully, as it is under tension and can be dangerous.

Step 4: Remove the Cable

Using pliers, disconnect the cable from the bottom bracket of the garage door. Next, release the cable from the drum by loosening the set screws on the drum with a wrench. Carefully unwind the cable from the drum, being sure to keep a firm grip on the cable to prevent it from unraveling.

Step 5: Install the New Cable

Install the new cable by winding it around the drum in the opposite direction of the old cable. Be sure to wind the cable evenly and tightly to ensure smooth operation. Once the cable is properly wound around the drum, thread the cable through the bottom bracket and attach it securely with pliers.

Step 6: Reattach the Spring

Reattach the spring by using a winding bar to turn the spring in the same direction as the cable until it reaches the appropriate tension.

Step 7: Test the Door

Test the garage door to ensure that it is functioning properly. Open and close the door several times to ensure that it is moving smoothly and without any problems.

Step 8: Reconnect the Power

Once you have confirmed that the garage door is functioning properly, reconnect the power by plugging in the garage door opener or turning on the circuit breaker.

Conclusion

As stated in Garage Door Parma OH, fixing a garage door cable can be a complex and potentially dangerous process. If you are not comfortable working with garage doors, it is recommended that you hire a professional garage door technician to perform the repair. Additionally, it is important to inspect your garage door cables regularly to prevent damage and ensure the safe operation of your garage door.

Parma Garage Door Repair

3710 Albertly Ave #8, Parma, OH 44134

440-762-6587

Page 2 of 9

Previous

Next

Powered by WordPress & Theme by Anders Norén