Going Green Homes VA Blog

Local Businesses Blog in Texas

Month: March 2023 Page 1 of 5

How to Remove Your Garage Door Seal – Springtown TX Garage Door

By

On March 31, 2023

In garage door repair

Removing a garage door seal can be a relatively simple task, and it can typically be done using basic tools.

Here are some steps you can follow to remove a garage door seal in reference to Garage Door Springtown TX:

  1. Prepare your work area

Start by clearing out the area around your garage door to provide enough space to work safely. Remove any obstacles, debris or equipment that may obstruct your movement.

  1. Locate the garage door seal

The garage door seal is located along the bottom of the garage door, attached to the door itself or the door frame. Identify the location of the seal and carefully inspect it for any damages or wear.

  1. Remove the screws or nails holding the seal in place

Most garage door seals are attached to the garage door or frame using screws or nails. Using a screwdriver or pry bar, remove any screws or nails holding the seal in place. Place the screws or nails in a container or bag to avoid losing them.

  1. Pull the seal off the garage door

Once you have removed the screws or nails, carefully pull the seal away from the door. Be gentle to avoid damaging the door or the seal.

  1. Remove any adhesive or residue

Once you have removed the seal, you may need to remove any adhesive or residue left behind. Use a scraper or putty knife to scrape away any remaining adhesive or residue from the door or frame. You can also use a commercial adhesive remover if necessary.

  1. Clean the garage door

After removing the seal and any adhesive residue, clean the garage door using a mild detergent and water. Rinse the door thoroughly with clean water and allow it to dry completely before installing a new seal.

In conclusion, as stated in Garage Door Springtown TX, you should be able to safely and effectively remove a garage door seal. It is important to take care when removing the seal to avoid damaging the door or the frame, as this can lead to costly repairs. If you’re not comfortable doing this work yourself, it is recommended to hire a professional garage door technician to help you.

Springtown TX Garage Door

205 Ave A, Springtown, TX 76082

817-373-5963

How to Disconnect Garage Door from Motor – Affordable Garage Door of Hamilton County

By

On March 31, 2023

In garage door repair

Disconnecting your garage door from the motor is an important step if you need to perform maintenance on the door or if you need to operate the door manually in the event of a power outage or other issue.

Here’s how to disconnect your garage door from the motor as per Garage Door Hamilton IN:

  1. Locate the emergency release cord

The emergency release cord is typically located near the top of the garage door motor unit. It will be a red cord hanging from the motor.

  1. Pull the emergency release cord

To disconnect the door from the motor, pull the emergency release cord down and towards the door. This will disengage the motor from the door and allow you to operate the door manually.

  1. Lift the garage door manually

Once you’ve pulled the emergency release cord, you should be able to lift the garage door manually. Be sure to lift the door evenly from both sides to avoid causing damage to the door or tracks.

  1. Secure the garage door

After you’ve lifted the door, you’ll need to secure it in place to prevent it from falling. Most garage doors will have a locking mechanism that you can engage to hold the door in place. If your door does not have a locking mechanism, you can use a clamp or other device to hold the door in place.

  1. Reconnect the garage door to the motor

When you’re ready to reconnect the garage door to the motor, simply lift the door until it’s level with the motor unit and pull the emergency release cord in the opposite direction to re-engage the motor. You should hear a click or other sound when the motor is re-engaged.

In conclusion, as stated in Garage Door Hamilton IN, it’s important to note that operating your garage door manually should only be done in emergency situations or when performing maintenance on the door. For regular use, you should always use the motor to open and close the door to avoid causing damage to the door or tracks. If you’re unsure how to safely disconnect your garage door from the motor, it’s always best to consult with a professional garage door technician who can provide you with the appropriate guidance and assistance.

Affordable Garage Door of Hamilton County

27361 Mosbaugh Rd. Arcadia, IN 46030

317-342-8167

How Much are Garage Doors in Costco? – Lakewood Garage Door Repair

By

On March 30, 2023

In garage door repair

Costco offers a variety of garage doors for sale both online and in-store. The cost of a Costco garage door can vary depending on a number of factors, including the size of the door, the type of material used, and any additional features or accessories that are included.

According to Lakewood Garage Door, at the time of writing this answer in March 2023, Costco’s website shows that they offer a range of garage doors that range in price from approximately $500 to $2,500 or more. The price includes the cost of the door itself, as well as any installation or delivery fees that may apply.

Costco’s garage doors come in a variety of materials, including steel, aluminum, wood, and composite. Steel doors are the most popular and are often the least expensive option. Aluminum doors are lightweight and rust-resistant, making them a good choice for coastal areas. Wood doors offer a classic look but require more maintenance than other materials. Composite doors offer the look of wood without the maintenance.

The cost of a Costco garage door can also be influenced by the size of the door. Most residential garage doors are between 8 and 18 feet wide and 7 to 8 feet tall. Larger doors, such as those used in commercial or industrial settings, can be more expensive.

Additional features or accessories can also add to the cost of a Costco garage door. For example, insulated doors are more expensive than non-insulated doors, but they can help to improve energy efficiency and reduce noise. Windows, decorative hardware, and special finishes can also add to the cost of a garage door.

Costco also offers installation services for their garage doors, which can add to the total cost of the door. The cost of installation can vary depending on the size of the door, the complexity of the installation, and the location of the installation.

In addition to the cost of the door itself, Costco’s garage doors come with a warranty that can range from one to five years. The warranty covers defects in materials and workmanship, and some warranties also cover the cost of repairs or replacement if the door fails to operate properly.

Overall, based from Lakewood Garage Door, the cost of a Costco garage door can vary depending on a number of factors, including the size, material, and features of the door. It is important to carefully consider these factors when choosing a garage door and to budget accordingly. Costco offers a range of garage doors to fit different budgets and needs, and their installation services can help to ensure that the door is installed safely and correctly.

Lakewood Garage Door Repair

1422 Elmwood Ave #7, Lakewood, OH 44107, United States

216-510-9359

How Far Away Can a Garage Door Opener Work? – First Call Garage Door Sugar Land

By

On March 30, 2023

In garage door repair

The range at which a garage door opener can work can vary depending on several factors, such as the type of opener, the strength of the signal, and any obstructions or interference in the area.

According to Garage Door Missouri TX, most garage door openers have a range of 100-200 feet (30-60 meters), although some higher-end models can have a range of up to 1,000 feet (305 meters) or more. However, the effective range of a garage door opener can be reduced by various factors, including walls, trees, and other obstacles that can block or weaken the signal.

There are two main types of garage door openers: chain-driven and belt-driven. Chain-driven openers use a metal chain to move the door, while belt-driven openers use a rubber belt. Belt-driven openers tend to be quieter and smoother than chain-driven openers, but they may also be more expensive.

Most garage door openers use radio signals to operate, with the remote control sending a signal to a receiver in the opener unit. The signal is usually in the 300-400 MHz frequency range, which allows it to pass through walls and other obstructions. Some newer openers use Bluetooth or Wi-Fi signals, which can have longer ranges but may also be more vulnerable to interference.

To ensure that a garage door opener works reliably and consistently from a distance, it is important to choose a high-quality opener with a strong signal and to test the range before installation. Homeowners can also improve the range of their garage door opener by adding an external antenna or upgrading to a stronger transmitter.

Most garage door openers come with a remote control that operates on batteries, and these batteries can affect the range of the opener. Weak or dead batteries can cause the signal to be weaker, reducing the effective range of the opener. Therefore, it is important to replace the batteries in the remote control regularly to ensure the opener works optimally.

It is also important to ensure that the garage door opener is installed properly and that the safety sensors and other components are functioning correctly. If the safety sensors are misaligned or malfunctioning, the opener may not work reliably or may stop working altogether. Regular maintenance and inspection of the opener can help identify and address any issues before they become major problems.

In addition to the opener itself, other factors can affect the range of a garage door opener, such as interference from other electronic devices or structures in the area. For example, large metal structures, such as buildings or other garage doors, can interfere with the radio signal and reduce the effective range of the opener.

Some openers have a “rolling code” system that changes the code each time the remote control is used. This can help prevent unauthorized access to the garage by making it more difficult for someone to intercept and duplicate the signal. However, the rolling code system can also affect the range of the opener, as it requires more processing power to generate and interpret the codes.

Overall, as stated in Garage Door Missouri TX, the effective range of a garage door opener can vary based on several factors, and homeowners should choose an opener that has a strong signal and is suitable for their particular needs. By testing the range before installation, ensuring proper installation and maintenance, and addressing any potential sources of interference, homeowners can ensure that their garage door opener works reliably and consistently from a distance.

First Call Garage Door Sugar Land

2865 Dulles Ave, Missouri City, TX 77459, United States

281-603-9929

How Do You Paint a Steel Garage Door – LMS Garage Door Roseville

By

On March 29, 2023

In garage door repair

Painting a steel garage door can be a great way to give your home a fresh, new look and increase its curb appeal. However, it is important to properly prepare the surface and use the right tools and techniques to ensure a smooth, long-lasting finish.

In this guide, we will take you through the step-by-step process from Garage Door Roseville CA of painting a steel garage door.

Materials Needed:

  • Sandpaper (220 grit)
  • Tack cloth
  • Painter’s tape
  • Drop cloths
  • Paint primer for metal
  • Paint (acrylic or oil-based)

Step 1: Clean the Surface The first step in painting a steel garage door is to thoroughly clean the surface. Use a mild detergent and water to remove any dirt, dust, or debris from the door. Rinse the door with clean water and allow it to dry completely before moving on to the next step.

Step 2: Sand the Surface Once the surface is clean and dry, use a 220-grit sandpaper to lightly sand the door. This step helps to create a rough surface that the primer can adhere to. Use a tack cloth to remove any dust or debris left behind after sanding.

Step 3: Apply Painter’s Tape Use painter’s tape to cover any areas of the garage door that you do not want to paint. This may include the door handles, windows, or any other hardware.

Step 4: Prime the Surface Apply a primer specifically designed for use on metal surfaces. Apply a thin coat of primer to the entire surface of the garage door. Use a brush or roller to apply the primer, and be sure to follow the manufacturer’s instructions for drying time.

Step 5: Sand the Surface Again Once the primer is dry, use a 220-grit sandpaper to lightly sand the surface again. This step helps to create an even smoother surface for the paint to adhere to. Use a tack cloth to remove any dust or debris left behind after sanding.

Step 6: Apply the Paint Apply the paint to the surface of the garage door using a brush or roller. Be sure to use a paint that is specifically designed for use on metal surfaces. Apply a thin coat of paint and allow it to dry completely before applying additional coats. Follow the manufacturer’s instructions for drying time and number of coats needed.

Step 7: Remove the Painter’s Tape Once the paint is completely dry, carefully remove the painter’s tape from the garage door.

Tips and Tricks:

  • Be sure to apply the paint in thin, even coats to prevent drips and runs.
  • Use a high-quality brush or roller to ensure a smooth finish.
  • If you need to apply multiple coats of paint, be sure to lightly sand the surface with 220-grit sandpaper between coats.
  • If you are using an oil-based paint, be sure to properly dispose of any rags or other materials that have come into contact with the paint to prevent the risk of fire.
  • Avoid painting in extreme temperatures or direct sunlight, as this can affect the drying time and the final finish.

In conclusion, as per Garage Door Roseville CA, painting a steel garage door requires proper preparation and the use of the right materials and techniques. By following the step-by-step process outlined above, you can achieve a smooth, long-lasting finish that will enhance the appearance of your home.

LMS Garage Door Roseville

10341 Fairway Dr, Roseville, CA 95678, United States

916-398-2078

How to Change Battery in LiftMaster Garage Door Opener – Acclaim Garage Door of Chandler

By

On March 28, 2023

In garage door repair

LiftMaster is a popular brand of garage door opener that is known for its reliability and ease of use. Like all garage door openers, LiftMaster openers rely on batteries to power their remotes and keypads. Over time, the batteries in these devices will wear out and need to be replaced. In this article, we will discuss the steps to change the battery in a LiftMaster garage door opener remote.

Before we get started, according to Garage Door Chandler AZ, it’s important to note that the exact steps for changing the battery in your LiftMaster garage door opener remote may vary depending on the model you have. Be sure to consult the owner’s manual for your specific model for detailed instructions.

Step 1: Locate the Battery Compartment The first step in changing the battery in your LiftMaster garage door opener remote is to locate the battery compartment. On most models, the battery compartment is located on the back of the remote. To access the battery compartment, you may need to remove the battery cover by sliding it off or pressing a small button.

Step 2: Remove the Old Battery Once you have located the battery compartment, it’s time to remove the old battery. LiftMaster remotes typically use coin-cell batteries, such as CR2032 or CR2016. To remove the old battery, use a small flathead screwdriver or your fingernail to pop it out of its holder. Be sure to dispose of the old battery properly, as it may contain harmful materials.

Step 3: Install the New Battery After removing the old battery, it’s time to install the new one. Make sure that you insert the new battery with the correct orientation. Most LiftMaster remotes have a diagram or label that shows which side of the battery should be facing up. Once you have inserted the new battery, make sure that it is seated securely in its holder.

Step 4: Test the Remote Once you have installed the new battery, it’s time to test the remote to make sure that it is working correctly. Press the buttons on the remote to see if the garage door opens and closes as expected. If the remote is not working, you may need to try reprogramming it or consult the owner’s manual for troubleshooting tips.

Additional Tips:

  • Make sure that you use the correct type of battery for your LiftMaster remote. Using the wrong type of battery can cause the remote to malfunction or not work at all.
  • If you have multiple LiftMaster remotes, it’s a good idea to replace the batteries in all of them at the same time. This will ensure that all of your remotes are working correctly and prevent any unexpected issues.
  • If you’re having trouble removing the battery cover or installing the new battery, don’t force it. Consult the owner’s manual or contact LiftMaster customer support for assistance.

In conclusion, as per Garage Door Chandler AZ, changing the battery in your LiftMaster garage door opener remote is a simple process that can be done in just a few minutes. By following the steps outlined above, you can ensure that your remote is working correctly and avoid any unexpected issues with your garage door opener.

Acclaim Garage Door of Chandler

184 E Chilton Dr, Chandler, AZ 85225, United States

480-545-0538

How to Realign Garage Door Sensors? – Acclaim Garage Door Repair of Phoenix

By

On March 28, 2023

In garage door repair

Garage door sensors are an essential safety feature designed to prevent the door from closing on people or objects in its path. If the sensors are not properly aligned, the door may not close, or it may close improperly, which can pose a significant safety hazard. Fortunately, realigning garage door sensors is a relatively simple process that can be done with just a few tools.

Before attempting to realign the sensors, it’s important to ensure that the door is functioning correctly. Check for any damage or obstructions that may be preventing the door from opening or closing properly. If there is a problem with the door itself, it should be repaired before attempting to realign the sensors.

Once you have confirmed that the door is functioning correctly, it’s time to realign the sensors.

Here’s how to do it based from Phoenix Garage Door:

  1. Locate the sensors: The sensors are typically located near the bottom of the garage door, on either side of the opening. They are usually attached to the wall or the door frame with screws.
  2. Check the alignment: Look at the sensors to see if they are aligned properly. The two sensors should be facing each other directly, with no obstructions in between. If the sensors are not aligned, they will need to be adjusted.
  3. Adjust the sensors: To adjust the sensors, first, loosen the screws that hold them in place. Once the screws are loose, you can move the sensors to the correct position. Use a level to ensure that both sensors are at the same height and facing each other directly.
  4. Tighten the screws: Once the sensors are aligned properly, tighten the screws to secure them in place. Be careful not to over-tighten the screws, as this can damage the sensors.
  5. Test the sensors: Test the sensors by opening and closing the garage door. If the sensors are properly aligned, the door should close without any issues. If the door still doesn’t close, you may need to repeat the process or call a professional for further assistance.

It’s important to note that garage door sensors are a safety feature and should be checked regularly to ensure that they are functioning correctly. Realignment may be necessary from time to time, especially if the sensors have been bumped or moved. Keeping the sensors in good working order can help prevent accidents and injuries.

In addition to realigning the sensors, there are a few other things you can do to ensure that your garage door is functioning correctly:

  1. Check the tracks: The tracks that guide the garage door should be clean and free from debris. If the tracks are dirty or obstructed, the door may not function properly.
  2. Lubricate moving parts: Use a silicone-based lubricant to lubricate the moving parts of the garage door, such as the springs, hinges, and rollers. This will help the door move smoothly and quietly.
  3. Check the springs: The springs that support the weight of the garage door can wear out over time. If the springs are damaged or worn, they will need to be replaced.
  4. Call a professional: If you are not comfortable working on your garage door, or if you are not sure what is causing the problem, it’s best to call a professional for assistance. A garage door technician can diagnose the problem and make the necessary repairs to ensure that your door is functioning safely and correctly.

In conclusion, as per Phoenix Garage Door, realigning garage door sensors is a simple process that can help prevent accidents and injuries. By following these steps and taking care of your garage door, you can ensure that it functions correctly and safely for years to come.

Acclaim Garage Door Repair of Phoenix

1107 E Bell Rd UNIT 16, Phoenix, AZ 85022, United States

602-833-1218

How Often Do Garage Doors Need to be Replaced – Garage Door Experts of Boynton Beach

By

On March 24, 2023

In garage door repair

The lifespan of a garage door can vary depending on several factors, including the type of door, the quality of the materials, the frequency of use, and the level of maintenance performed.

Based from Boynton Beach Garage Door, here are some general guidelines for how often different types of garage doors may need to be replaced:

  1. Steel Garage Doors – Steel garage doors are a popular choice for their durability and low maintenance requirements. A high-quality steel door can last for up to 20 years or more with proper maintenance. However, if the door is damaged or dented, it may need to be replaced sooner.
  2. Wood Garage Doors – Wood garage doors are a classic and elegant choice, but they require more maintenance than steel doors. With proper maintenance, a wood door can last for up to 20 years or more. However, wood doors are more susceptible to damage from moisture and weathering, so they may need to be replaced sooner if they are not properly maintained.
  3. Aluminum Garage Doors – Aluminum garage doors are lightweight and low maintenance, but they are not as durable as steel doors. An aluminum door may last for up to 15 years or more with proper maintenance, but it may need to be replaced sooner if it is damaged or dented.
  4. Fiberglass Garage Doors – Fiberglass garage doors are lightweight and low maintenance, but they are not as strong as steel or wood doors. With proper maintenance, a fiberglass door can last for up to 15 years or more. However, if the door is damaged, it may need to be replaced sooner.

It’s important to note that these are general guidelines, and the lifespan of your garage door may vary depending on your specific circumstances. Regular maintenance, including lubrication, tightening of hardware, and inspection for damage, can help prolong the lifespan of your garage door.

In summary, as stated in Boynton Beach Garage Door, if you’re unsure about the lifespan of your garage door, or if you’re experiencing problems with your door, it’s a good idea to consult with a professional garage door installer. They can help assess the condition of your door and recommend the best course of action, whether that’s repair, maintenance, or replacement.

Garage Door Experts of Boynton Beach

615 NE 7th Ave, Boynton Beach, FL 33435

561-861-2357

How to Change Garage Door Rollers? – Garage Door Experts of Lake Worth

By

On March 23, 2023

In garage door repair

Garage door rollers are an essential component of a garage door system that allow the door to move smoothly along the tracks. Over time, garage door rollers can wear out or become damaged, which can cause the door to operate poorly or become noisy.

In this article, we will provide step-by-step instructions from Garage Door Repair Lake Worth FL on how to change garage door rollers.

Tools and Materials Needed:

  • Replacement garage door rollers
  • Wrench or socket set
  • Pliers
  • Flathead screwdriver
  • Lubricant
  • Ladder
  • Safety glasses

Step 1: Safety First Before beginning any work on the garage door, it’s important to take proper safety precautions. Wear safety glasses to protect your eyes from debris and always disconnect the garage door opener from the power source to prevent any accidental opening or closing of the door.

Step 2: Open the Garage Door Open the garage door completely to access the rollers. You may need to use a ladder to reach the rollers on the top panel of the door.

Step 3: Remove the Old Rollers Using a wrench or socket set, remove the bolts or nuts that hold the old rollers in place. Use pliers to hold the roller stem while removing the bolts or nuts to prevent the roller from falling out. Once the bolts or nuts are removed, carefully slide the roller out of the track and remove it.

Step 4: Clean the Track Use a flathead screwdriver to remove any debris or buildup from the track. Clean the track thoroughly to ensure that the new rollers can move smoothly.

Step 5: Install the New Rollers Insert the stem of the new roller into the track and slide it into place. Secure the roller by tightening the bolts or nuts with a wrench or socket set. Repeat this process for each roller on the door.

Step 6: Lubricate the Rollers Once all of the new rollers are installed, lubricate them with a silicone-based lubricant. Apply a small amount of lubricant to each roller and allow it to penetrate the bearings.

Step 7: Test the Door After replacing the rollers and lubricating them, test the door to ensure that it is operating smoothly and quietly. Open and close the door a few times to make sure that the rollers are functioning properly.

Step 8: Clean Up Clean up any debris or tools that were used during the installation process. Dispose of any old rollers properly.

In conclusion, as per Garage Door Repair Lake Worth FL, replacing garage door rollers is a relatively simple process that can be done with a few basic tools and some safety precautions. By following these step-by-step instructions, you can ensure that your garage door operates smoothly and quietly for years to come. If you encounter any issues during the installation process or are unsure about how to proceed, it’s always best to consult a professional garage door technician for assistance.

Garage Door Experts of Lake Worth

714 4th Ave N, Lake Worth, FL 33460

561-462-5171

How To Oil Garage Door – Strongsville Garage Door Repair

By

On March 23, 2023

In garage door repair

Maintaining your Garage Door Repair Strongsville OH is essential for it to function properly and last a long time. One of the most important parts of garage door maintenance is keeping the door properly lubricated. This not only helps keep the door working smoothly but also prevents wear and tear on the moving parts.

In this article, we will discuss how to oil a garage door, step by step:

Step 1: Gather Your Supplies

Before you begin, you will need to gather a few supplies. You will need:

  • A can of lubricant (spray or liquid)
  • A rag or cloth
  • Safety glasses
  • Gloves

Step 2: Inspect the Door

Before you start lubricating, inspect the door for any visible signs of wear or damage. Look for cracks, dents, or rust on the tracks and rollers. Make sure all the bolts and screws are tight, and there are no loose parts.

Step 3: Clean the Door

Once you have inspected the door and made any necessary repairs, clean the door and its components. Use a damp cloth to remove any dirt, dust, or debris that has accumulated on the door and its parts.

Step 4: Lubricate the Tracks

Apply a small amount of lubricant to the tracks on both sides of the garage door. Make sure to apply the lubricant evenly, and use enough to cover the entire track. Move the door up and down a few times to ensure the lubricant is evenly distributed.

Step 5: Lubricate the Rollers

Next, apply lubricant to the rollers. Place a rag or cloth under the roller to catch any drips. Spray or apply the lubricant on the roller and the shaft. Move the door up and down a few times to ensure the lubricant is evenly distributed.

Step 6: Lubricate the Hinges

Apply lubricant to the hinges on both sides of the door. Make sure to apply the lubricant to the pivot points and the pins. Move the door up and down a few times to ensure the lubricant is evenly distributed.

Step 7: Lubricate the Springs

Finally, apply lubricant to the springs. This is a critical step as the springs are under a lot of tension, and lubricating them properly will prevent them from breaking prematurely. Use caution when working with the springs, as they can be dangerous. Apply lubricant to both the torsion and extension springs.

Step 8: Wipe off Excess Lubricant

After you have lubricated all the moving parts, wipe off any excess lubricant with a clean cloth. Be sure to wipe down the tracks and rollers, as excess lubricant can attract dirt and dust, which can cause the door to stick.

Step 9: Test the Door

Once you have finished lubricating the door, test it to make sure it is working properly. Open and close the door a few times to make sure it moves smoothly and there are no strange noises or vibrations.

Step 10: Repeat as Needed

Garage doors should be lubricated at least once a year. However, if you use your garage door frequently or live in an area with extreme temperatures, you may need to lubricate your door more frequently. Repeat the steps above as needed to keep your garage door working smoothly.

In conclusion, lubricating your Garage Door Repair Strongsville OH is an essential part of maintenance that can prolong the life of your door and prevent costly repairs. By following the steps above, you can easily lubricate your garage door and ensure it continues to function properly for years to come.

Strongsville Garage Door Repair

440-271-8232

Page 1 of 5

Next

Powered by WordPress & Theme by Anders Norén